四虎网站在线观看,亚洲人久久久综合网站,欧美狠狠鲁,黄色网络久久2

服務熱線: 400-117-8816
           13406879330

扭剪扳手,扭剪螺栓專用扳手,扭剪電動扳手,扭剪槍生產廠家

當前位置:首頁>技術文獻電動扭剪扳手專門用于緊固高強度扭剪螺栓

電動扭剪扳手專門用于緊固高強度扭剪螺栓

來源:http://8ying.cn日期:2022-10-07 發布人:admin

電動扭剪扳手專門用于緊固高強度扭剪螺栓,并且在緊固完成后將剪斷的梅花頭保留在套筒內部不掉落,隨后扣動扳機將梅花頭彈出,動力為220V或110V交流電源,相比較與傳統六角螺栓,扭剪螺栓配合電動扭剪扳手,施工方便快捷,扭矩控制準確并且方便檢查。

The electric torque shear wrench is specially used to fasten high-strength torque shear bolts, and after the fastening is completed, keep the cut torx head inside the sleeve, and then pull the trigger to eject the torx head. The power is 220V or 110V AC power supply. Compared with the traditional hexagon bolt, the torque shear bolt and the electric torque shear wrench are convenient and fast for construction, accurate torque control, and convenient for inspection.
扭剪型電動扳手使用:
Use of twist shear type electric wrench:
1、用扳手內套筒完全插進螺栓尾部梅花頭部分,同時向前推動扳手,內套筒后退,使外套筒完全套住螺母,若不能完全套住螺母請左右轉動扳手并向前用力。
1. Insert the inner sleeve of the wrench fully into the box head at the end of the bolt, push the wrench forward at the same time, and the inner sleeve moves backward to make the outer sleeve completely cover the nut. If the nut cannot be completely covered, turn the wrench left and right and force forward.
2、扣動扳手開關,使其旋轉。
2. Turn the wrench switch to rotate it.
3、擰斷梅花頭,緊固結束,彈出梅花頭即可。
3. Screw off the plum blossom head, fasten it, and pop it out.
扭剪型電動扳手注意事項:
Precautions for twist shear type electric wrench:
1、不可在雨天或潮濕的環境中使用本機,以免漏電。
1. Do not use the machine in rainy days or humid environments to avoid electric leakage.
2、使用本機高空作業時,請系好帶,在操作點下方嚴禁站人及放置貴重物品。
2. When using this machine to work at heights, please fasten your safety belt. It is strictly forbidden to stand under the operation point and place valuables.
3、使用本機時需遠離易燃易爆物品。
3. Keep away from inflammables and explosives when using this machine.
4、嚴禁破壞電源線及使用電源線拖拉本機。
4. It is forbidden to damage the power cord or use the power cord to drag the machine.
5、檢查及維修本機時應先切斷電源。
5. Cut off the power supply before checking and repairing the machine.
扭剪型電動扳手檢查與維修:
Inspection and maintenance of torsional shear type electric wrench:
1、定期檢查碳刷,建議碳刷小于7mm時進行更換。
1. Check the carbon brush regularly. It is recommended to replace the carbon brush when it is less than 7mm.
2、保持內外套筒清潔不得混入雜物。用完本機后應擦拭干凈存放于干燥處。
2. Keep the inner and outer sleeves clean and free of sundries. After using the machine, it should be wiped clean and stored in a dry place.
3、使用前應檢查各緊固螺釘是否松動,如果松動應及時緊固,并試轉聲音是否正常,如果出現異常聲音應及時檢修。
3. Before use, check whether the fastening screws are loose. If they are loose, tighten them in time, and check whether the sound of trial run is normal. If there is abnormal sound, repair them in time.
以上就是為大家介紹的有關扭剪扳手的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://8ying.cn
The above is a detailed introduction to the torque shear wrench. I hope it will be helpful to you. If you have any questions, please contact us. We will provide you with professional services http://8ying.cn

一区二区三区,在线| 天天综合色情网站| 亚洲无码精品爱| 黄片久久免费| 亚洲一三区特黄无码| 黄色成人91免费看| 婷婷最新加勒比| 在线观看无码观看一区| 欧州丰满人妻| 第一区第二区福利微拍| 亚洲色综合| 偷拍自拍 欧美电影| 欧美一区二区三区自拍人妻欧美合集| 亚洲精品白浆高清久久久久| 传媒av网页在线| 伊人大香蕉后| 亚洲久久久一区二区| 伊人午夜福利| 草b免费视频观看AI识别| 女不卡视频二区| 亚洲国产久久黄色片| 人人澡人人捏揉| 免费在线观看AV不卡| 偷拍磁力久久| 日韩夜夜夜夜久| 国产精品大尺度在线| 午夜福利亚洲一区二区三区| 男人的天堂AV超男人| WWW婷婷久久中文| 国产在ww| 日本新一区二区三区四区| 美女操BAV国产| 在线成人pmv 兔子舞 亚洲| 就爱人妻av| 欧美精品第84页| Av 一区二区 蜜桃 麻豆| 久久久久久.com.| 日韩三级片一区二区久久| 青青草国产区一区AV| 激情涩婷婷涩五月天婷婷| 久久久亚洲福利精品午夜|