Torque wrench calibration instrument operation method, SGXJ Torque wrench calibrator is used to calibrate the torque wrench tester. Torque wrench calibrator is a high performance test instrument, which has been widely used in power, light industry, machinery, engine, internal combustion engine, electric vehicle, motorcycle, automobile, ship, aircraft and other manufacturing and measurement and testing departments.

　　大家知道扭矩扳手校準器的操作方法嗎?-電動扭矩扳手:http://8ying.cn

　　Do you know how to operate the torque wrench calibrator? - Electric torque wrench: http://8ying.cn

　　扭矩扳手校準器的操作方法

　　Operation Method of Torque Spanner Calibrator

　　1. 使用扭矩扳手校準儀前，應檢查儀器電量是否充足。如電量不足，請先充電(充電時也可使用)。

　　1. Before using the torque wrench calibrator, check whether the power of the instrument is sufficient. If the electricity is insufficient, please charge it first (it can also be used when charging).

　　2. 將被測件的被測頭放入被測件的被測孔內，用被測件另一端的手柄置于高度調節塊上方(如長度不足，可自由調節整個加載裝置)。

　　2. Put the measured head into the tested hole, and place the handle at the other end of the measured piece above the height adjustment block (if the length is insufficient, the whole loading device can be adjusted freely).

　　3.打開電源開關，顯示的轉矩值為零。如果不為零，按“復位”按鈕復位扭矩值。

　　3. Turn on the power switch and the display torque is zero. If it is not zero, press the "reset" button to reset the torque value.

　　4. 測試前，設置上下限、比較小存儲值、比較小峰值保持值、自動峰值時間、自動關機時間、重力加速度等。

　　4. Before testing, upper and lower limits, minimum storage value, minimum peak holding value, automatic peak time, automatic shutdown time, gravity acceleration and so on are set.

　　(1)上限設置:用戶設置上限，可根據需要自由設置。當達到上限時，表示自動聲光提示，上限不高于全量程。

　　(1) upper limit setting: users can set the upper limit freely according to their needs. When the upper limit is reached, it means automatic acoustooptic prompt, and the upper limit is not higher than the full range.

　　(2)下限設置:用戶根據需要自由設置下限。當達到下限時，表示自動照明提示。下限不得高于規定的上限。

　　(2) Lower Limit Setting: Users are free to set the lower limit according to their needs. When the lower limit is reached, the automatic illumination prompt is indicated. The lower limit shall not exceed the prescribed upper limit.

　　(3)比較小存儲值設置:用戶根據存儲需求設置比較小存儲值。小于此值的數據將不存儲。

　　(3) Minimum Storage Value Settings: Users set Minimum Storage Value according to storage requirements. Data less than this value will not be stored.

　　(4)比較小峰值設置:用戶需要根據峰值設置自動測峰，小于峰值的數據不會被峰值保存。

　　(4) Minimum Peak Settings: Users need to set automatic peak measurement according to the peak value. Data smaller than the peak value will not be saved by the peak value.

　　(5)自動峰值時間設定:用戶可根據自動峰值測量狀態，自由設定1秒99秒的峰值時間。

　　(5) Automatic peak time setting: users can freely set the peak time from 1 second to 99 seconds according to the automatic peak measurement status.

　　大家知道扭矩扳手校準器的操作方法嗎?-電動扭矩扳手:http://8ying.cn

　　Do you know how to operate the torque wrench calibrator? - Electric torque wrench: http://8ying.cn

　　6、自動關機時間設置:在無運行狀態下，可自由設置0分鐘9分鐘的自動關機時間(設置為0分鐘時，表示取消自動關機)。

　　6. Automatic shutdown time settings: In the non-operating state, the automatic shutdown time can be set freely from 0 minutes to 9 minutes (set to 0 minutes, which means canceling the automatic shutdown).

　　7、重力加速度設置:用戶可以根據該區域的位置設置重力加速度值，默認為9.794。

　　7. Gravity acceleration settings: Users can set the value of gravity acceleration according to the location of the area, default is 9.794.

　　今天恢復初始設置:用戶操作不當或多次更改數據混淆，可以通過此設置將1 ~ 7個數據恢復到出廠狀態。以上 是電動扭矩扳手為大家整理的相關內容，想要了解更多內容，歡迎訪問我們網站：http://8ying.cn

　　Restore the initial settings today: Users can restore 1 to 7 data to factory status through improper operation or multiple changes in data confusion. These are the related contents of the electric torque wrench for you. For more information, please visit our website: http://8ying.cn.